restastro.blogg.se - Asa has red alarm light

The interface numbers that appear in the Firebox configuration depend on the number of ports on the interface module, and the interface module slot where the interface module is installed.

WatchGuard Firebox M 2 Port 40 Gb QSFP+ Fiber Module - WatchGuard SKU WG8023įor each interface module, ports are numbered from 0-7, 0-3, or 0-1.WatchGuard Firebox M 4 Port 10 Gb SFP+ Fiber Module - WatchGuard SKU WG8594.WatchGuard Firebox M 8 Port SFP Fiber Module - WatchGuard SKU WG8593.WatchGuard Firebox M 8 Port 1 Gb Copper Module - WatchGuard SKU WG8592.You can purchase these compatible interface modules from an authorized WatchGuard reseller: To avoid damage to the system, power off the Firebox before you install or remove interface modules. For instructions to install or remove interface modules, see Interface Module Installation. You must install the interface module before you can configure the interfaces. To add more interfaces to your Firebox, you can install an interface module in an available interface module slot. The left indicator shows interface activity.

The right indicator shows the interface connection status. Interfaces 0 - 7 are RJ45 Ethernet interfaces that support link speeds of 10, 100, or 1000 Mbps. The management interface is interface 24. You must connect to this interface to configure the Firebox when it starts with factory-default settings. The management interface, labeled or Mgmt, is located to the right of the USB interfaces. You can connect to this serial interface to log in to the Fireware Command Line Interface.įor more information about the command line interface, see the current Command Line Interface Reference available on the Firebox documentation page at. For more information, see Fireware Help.Īn RJ45 connector for the serial (console) interface is located above the USB interfaces. Connect a USB storage device for USB backup and restore, or to store a support snapshot. The Firebox M4800 has eight built-in network interfaces, a management interface, two USB interfaces, and one serial console port. To reset the device, see Restore Factory Default Settings Built-in Interfaces The Reset button, located to the left of the USB interfaces, resets the device to factory-default settings. The Firebox does not power off if you briefly press the Power button. When the Power button is green, press and hold the power button for five seconds to power off theįirebox. When the Power button is red, press it to power on the Firebox. It is green when the Firebox is powered on, and red when power is available, but the Firebox is powered off. The Power button is lit to indicate power status. When there is activity on the internal storage, this indicator is yellow. When the device is powered on, but not ready to pass traffic, this indicator is red. When the device is armed and ready to pass traffic, this indicator is green. The power indicator is green when the device is powered on. This table shows other environmental requirements for the M4800 appliance.

Connect it to a conditioned power supply to prevent damage from sudden power changes.

Put it in a secure area, such as a locked room, to block the device from people who do not have permission to use it.

To safely install your Firebox, we recommend that you: The supported interface modules are described in the Slots where you can install additional interface modules. This table shows the interface specifications for the WatchGuard M4800 as shipped. This table shows the hardware specifications for the WatchGuard Firebox M4800. About Your Hardware Hardware Specifications For more information on the features of Fireware OS, see Fireware Help. Each Firebox M4800 device includes Fireware OS and delivers exceptional protection against today's sophisticated threats to make sure that your business stays connected. The Firebox M4800 device uses WatchGuard’s next generation UTM OS - Fireware OS. The Firebox M4800 consolidates critical network and security functions into a single, centrally managed device, and is ideal as the ‘hub’ for distributed, hub-and-spoke type deployment scenarios. This guide introduces the Firebox M4800, a RoHS-compliant (lead-free) hardware product offered by WatchGuard. Powerful subscription-based security services deliver in-depth defenses against advanced malware, ransomware, botnets, trojans, viruses, drive-by downloads, phishing and much more. WatchGuard security appliances deliver unparalleled unified threat management, superior performance, ease of use, and value.